Riverton Foundation Pros logoRiverton Foundation ProsFoundation Repair · Draper, UT
Driveway Lifting photo

Riverton Foundation Pros

Driveway Lifting in Draper, UT

Driveway lifting in Draper, UT raises sunken slabs near the garage with polyurethane foam, drive-ready same day, with free estimates.

  • 15+ Years local experience
  • 500+ Projects completed
  • Licensed & Insured

Serving Draper and nearby communities.

Driveway lifting raises a sunken driveway slab back to grade, most often right where it meets the garage apron where vehicle weight concentrates over backfilled soil. On Draper's newer builds, that fill keeps settling for years after construction, and the slab edge nearest the garage door is usually the first place it shows.

Riverton Foundation Pros lifts with polyurethane foam injected through dime-sized holes rather than demolishing and repouring, which keeps the driveway usable the same day instead of out of service for a week.

What's included

What's included with Driveway Lifting

Typically included: - Optional: Customer prep:

  • Driveway inspection and slope measurement — Access holes drilled at each low point -.
  • Foam injection and slope correction — Hole sealing and surface review.
  • Joint sealant on adjoining expansion joints
  • Surface sealer applied after patching
  • Move vehicles off the driveway for the scheduled work window
  • Note any pooling near the garage door after rain

How it works

How our Driveway Lifting process works

  1. Driveway Inspection photo
    Step 1

    Driveway Inspection

    Sunken or sloped sections are identified for correction.

  2. Access Drilling photo
    Step 2

    Access Drilling

    Small holes are drilled at strategic points along the driveway.

  3. Foam Injection photo
    Step 3

    Foam Injection

    Expanding foam is pumped beneath the slab to raise it evenly.

  4. Slope Correction photo
    Step 4

    Slope Correction

    The surface is adjusted to restore proper drainage direction.

  5. Hole Sealing photo
    Step 5

    Hole Sealing

    Drilled holes are patched to blend with the existing surface.

  6. Surface Review photo
    Step 6

    Surface Review

    The driveway is inspected for even, stable elevation.

Materials

Materials and methods for Driveway Lifting

  • Polyurethane Foam photo

    Polyurethane Foam

    Lifts the slab without adding the water weight that can push already-compacting soil further out of place.

  • Concrete Patch Mix photo

    Concrete Patch Mix

    Seals access holes to a clean, flush finish after injection.

  • Joint Sealant photo

    Joint Sealant

    Reseals expansion joints disturbed by the lift so water doesn't collect in the gap.

  • Surface Sealer photo

    Surface Sealer

    Guards against Utah's freeze-thaw cracking once the slab is back at grade.

  • Leveling Equipment photo

    Leveling Equipment

    Keeps the lift accurate across a wide driveway slab, not just at one access point.

  • Bonding Primer photo

    Bonding Primer

    Improves patch adhesion where the new material meets the original concrete edge.

Timeline

How long does a Driveway Lifting take?

Most driveways are lifted and ready to drive on the same day.

  1. 01

    Inspection and marking

    same day
  2. 02

    Drilling and injection

    1–3 hours

    depending on slab size

  3. 03

    Cure time

    about 15 minutes before vehicle load

  4. 04

    Patch and finish

    same day

    right after lifting

Need a schedule that fits?

Get a Free Estimate

Before & after

Before and after Driveway Lifting results

  • Driveway Lifting photo
    Before
  • Driveway Lifting photo
    After

FAQs

Driveway Lifting FAQs

Why is my driveway sinking near the garage door?

The garage approach carries the heaviest concentrated vehicle load on the driveway, and it usually sits over soil that was backfilled during construction. As that fill compacts, the slab edge closest to the garage drops first.

Is polyurethane concrete lifting cheaper than replacing a slab?

Yes. Lifting avoids demolition and new-concrete costs and skips the multi-day cure time of a fresh pour, since the driveway is usable again within hours of the injection.

How long does driveway lifting take to cure?

The foam reaches full strength in about 15 minutes, so most driveways are ready for vehicle traffic the same day.

Will driveway lifting fix water pooling at the garage?

Lifting corrects the slab's slope, which often resolves pooling caused by a sunken low point. If the pooling comes from yard grading rather than the slab itself, a French drain may be needed alongside the lift.

Do I need a permit for driveway lifting?

No, . Foam lifting on an existing slab is considered a repair, not a structural replacement, so permitting usually isn't required.

Next step

Get a Driveway Lifting estimate in Draper

Call Riverton Foundation Pros at +1 (385) 600-7881 or request a free estimate for your sunken driveway.

Ask about Driveway Lifting

Tell us about the project and how to reach you.

Call (385) 600-7881